DUSTIN - WHAT IS THIS ON YOUR TURBO???????
#5
Member
Join Date: Jun 2001
Location: Houston, TX, USA
Posts: 2,082
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (Giuseppe)
Yeah, you should have one in your Drag kit. In fact, there should be two: one for the side port of your WG and one for the compressor. I connected a hose from that port to the bottom port of my Greddy Type S BOV and the top port to my intake manifold for better BOV response. You could also use it if you had an EBC like the AVCR or something.
#6
Honda-Tech Member
Join Date: Jun 2001
Location: Northern, VA
Posts: 7,261
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (maxim)
Maxim, how much more response did you get with the Bottom port on the Blow off valve connected to the Turbo compressor??
Thanks.
Thanks.
#7
Honda-Tech Member
Join Date: Jan 2000
Location: dirty jerzey, NJ, USA
Posts: 1,376
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (BG Boost)
just make sure that you connect the wastegate to some kinda strong vacume sorce or it will be nasty
Trending Topics
#8
Honda-Tech Member
Join Date: Oct 2000
Location: Zoo York
Posts: 4,534
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (PROFILE GSR)
just make sure that you connect the wastegate to some kinda strong vacume sorce or it will be nasty
#10
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (intekragsr)
noe more question. I notice the teflon tape is used on oil feed fitting which is not reconmond in drags installation manual, qoute "7) Install the 90 degree "AN" fitting to the center section (DO NOT use any Teflon tape and/or silicone on the fitting)"
So should I use the teflon tape or not??
So should I use the teflon tape or not??
#12
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (degradated)
You use teflon tape on NPT fittings, not AN fittings. AN fittings seal by pressure at the bevel, NPT fittings seal at the threads...
Dustin
Dustin
#13
New User
Join Date: Dec 2000
Location: RAIDER NATION, CA, USA
Posts: 6,415
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (dustin)
so it that vacuum source what you use for your boost controller? im still hesitating to put my boost controller on cuz if i mess up, i might blow my motor.
#15
Honda-Tech Member
Join Date: Jan 2000
Location: Sacramento, CA
Posts: 14,500
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (dlplayboy)
so it that vacuum source what you use for your boost controller? im still hesitating to put my boost controller on cuz if i mess up, i might blow my motor.
#17
New User
Join Date: Dec 2000
Location: RAIDER NATION, CA, USA
Posts: 6,415
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (dustin)
Better take your turbo off too, cause that might contribute to a blown motor...
#18
Honda-Tech Member
Join Date: Jan 2000
Location: TX, USA
Posts: 1,627
Likes: 0
Received 0 Likes
on
0 Posts
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (dustin)
Dustin I think you circled those Earl's fittings for me. We ordered them at the same time, but you got yours first. You were showing me how freakin LONG the barbed part of the fitting is. I'm still using the same ones!
#19
Re: DUSTIN - WHAT IS THIS ON YOUR TURBO??????? (MarkC)
Dustin I think you circled those Earl's fittings for me. We ordered them at the same time, but you got yours first. You were showing me how freakin LONG the barbed part of the fitting is. I'm still using the same ones!
[Modified by dangerzone, 8:29 PM 1/28/2002]
Thread
Thread Starter
Forum
Replies
Last Post
Civic Racer X 7
Forced Induction
6
05-27-2007 09:07 AM