|
egmatt93
Offline
560 posts [100%]
Everything gets stolen PA
11-22-2006
|
| « Re: putting back speakers in 93 eg hatch (heeltoeNdro) | « » 9:24 AM 5/14/2008 |
Reply
Edit
|
buy the brackets and covers from honda, the wires are already ran. there sitting behind the platics
Official bring NOFX back #09. If you ban NOFX, delete all the threads she took the time and hours she has done for you and everyone on this web site. She may have been cocky from time to time but she still did her best to help. -95 Teal Cx hatch ~b16a2*t~
|
speedooo
Offline
3069 posts [100%]
rollin no hood on 37 JERSEY
3-23-2005
|
| « Re: putting back speakers in 93 eg hatch (egmatt93) | « » 12:42 PM 5/14/2008 |
Reply
Edit
|
| Quote, originally posted by egmatt93 » | | buy the brackets and covers from honda, the wires are already ran. there sitting behind the platics |
x2
Pro-Jerkoff
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
ehmatt93, are you talking about the place where the 94-95 EGs have rear speakers? In the side panels next to the rear seats right? Those are what I actually wanted to find out about. I wanted to get some rear speakers but have them in the factory location. Do I have to get new rear panels? Is the speaker hole-less panel only a cover that I can remove or do I have to cut it or something?I think the OP is talking about putting rear speakers in the hatch area, behind the rear seats.
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
Sorry for stealing this thread a little bit but I wanted to ask this question myself.
Are you saying that I could get part 9/18 and replace my part 10/19 without replacing the whole panel (5/15)? Do my panels 10/19 just pop out from the outside or inside of the panel? And you said the wiring for the speaker is already in there if I remove my cover, right? And the bracket you are talking about is 11/20 I assume. Do I have to get all those little clips like 36,30, and 26 or do I already have any of them?
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
anyone know?
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
I also just found this when I was looking on majestic honda.
 Do I also need 2/3 and 6/8 and all those other little screws? Is there anything I already have behind my current covers and don't need to buy? Besides the speakers of course because I am buying my own.
|
wangg125
Online
37 posts [100%]
san francisco ca
11-10-2005
|
| Quote, originally posted by Dekorum » | | Sorry for stealing this thread a little bit but I wanted to ask this question myself.
Are you saying that I could get part 9/18 and replace my part 10/19 without replacing the whole panel (5/15)? Do my panels 10/19 just pop out from the outside or inside of the panel? And you said the wiring for the speaker is already in there if I remove my cover, right? And the bracket you are talking about is 11/20 I assume. Do I have to get all those little clips like 36,30, and 26 or do I already have any of them? |
yes, you can just get part 9/18 to replace 10/19.
no, you don't need to replace 5/15.
you pop out 10/19 panels from the outside of the panel. I use to just drop the backrest of the rear seats and use a flathead to pry the panel off.
the speaker wiring should be behind that panel, and yes you need 11/20.
as for the clips, i am not sure which ones you need or not...
| Quote, originally posted by jonebone » | | And all the sudden... common sense isn't so "common" after all |
|
wangg125
Online
37 posts [100%]
san francisco ca
11-10-2005
|
| Quote, originally posted by Dekorum » | I also just found this when I was looking on majestic honda.
Do I also need 2/3 and 6/8 and all those other little screws? Is there anything I already have behind my current covers and don't need to buy? Besides the speakers of course because I am buying my own. |
Just pull that panel off and see what brackets you need, that would be your best bet.
| Quote, originally posted by jonebone » | | And all the sudden... common sense isn't so "common" after all |
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
How do you pull of the panel? I want to know the correct way before I break it. So far I pulled on it from a corner and it wasn't doing anything.
|
wangg125
Online
37 posts [100%]
san francisco ca
11-10-2005
|
what i used to do is pry it with a flat head from the part that is closest to the rear seats and just pull the rest out. do this as if you were to pry open the front speaker covers.
| Quote, originally posted by jonebone » | | And all the sudden... common sense isn't so "common" after all |
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
Ok, I got you. I just wasn't sure if they were meant to be taken off like that. I felt like I was going to break something.
|
heeltoeNdro
Offline
254 posts [100%]
orlando fl
1-14-2007
|
i just see one wide wire when i pull off my panels is that the speaker wire???
|
scuzz
Offline
101 posts [100%]
Dalton GA
1-13-2007
|
What section is these parts located?
I tried to find them on majestic yesterday, and couldn't.
Thanks,
Ron
|
Skunk.Werks
Online
1452 posts [98%]
PA
8-22-2003
|
I think that all parts related to the mounting of rear speakers into EG hatches are long discontinued. However if you are in need, I have black speaker covers brand new in package so send me a PM if you are interested.I can also coach you on how to install these since I have installed the Gathers dual speaker setup in my HB
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
I popped off my panel and I didn't see any speaker wire. I only see the window washer line when I remove the driver side one.
|
heeltoeNdro
Offline
254 posts [100%]
orlando fl
1-14-2007
|
ya exact same thing with me where are the speaker wires yall speak of???
|
nonvtec92
Offline
332 posts [100%]
AL
2-15-2002
|
You have to reach down into the panel. They're probably clipped in somewhere down there. Mine were and i've got a base model 93 CX.Heck with buying brackets. I made some out of thin panel board. Cut a panel, cut a hole for my rear speakers... ran small bolts through the panel into the holes in the sheet metal that were already there and poof... speakers in the back. Everyone ALWAYS asks where the speakers are. They sound great without any holes in them or anything.
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
I'd personally rather use the brackets and keep it as OEM as possible without putting any holes through any thing. I think I will call majestic honda soon and see if they can tell me what exact parts I need. I will assume the speaker wires are going to be down there so I'll find them when I go to install my speakers.
|
nonvtec92
Offline
332 posts [100%]
AL
2-15-2002
|
Didn't put holes through anything. Three holes hold my bracket. Holes that were already in the sheet metal behind the plastic panels.Just thought i'd throw my wood panel board option.
Saved me who knows how much $$$ for those stupid metal brackets that only come on some.
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
Is part 6/8 necessary to put the speaker on the bracket? The reason I ask is because 6/8 and the little screws for it are discontinued and cannot be bought off Majestic or SL. Can I get speaker to go directly on the 2/3 brackets?
|
Dekorum
Offline
133 posts [100%]
4-17-2008
|
Anyone? And does the speaker come through the 11/20 part from the first picture?
|
| | |
