Print  Email  Subscribe  RSS  Help
 hondata s300 innovative lci install
Author Post

hybridmath




Offline

192 posts [99%]
northern ct
4-27-2005
  hondata s300 innovative lci install« » 7:32 PM 5/12/2008 Reply  Edit

dont know if this is the right place to post this but here i go

I recently purchased a hondata s300 with innovative wideband o2 and i cant find anything on how to replace the stock o2 with the wideband as a permant part i am new to all of this and may not be looking in the right places so if anyone could help with some diagrams or how-to it would be greatly appreciated i tried search function but appears to be down


Current : 94 dx hatchback fully built gsr getting rdy for boost
95 civic cx hatchback b18c1 apexi ws2 exhaust ran 14.611 stolen)
92 civic hatchback 00 integra B18b1 with gsr transmission 70 shot NOS (TOTALED)
93 civic 4dr b18a ys1 transmission (Totaled)



laziebun




Offline

343 posts [100%]
fort campbell ky
11-20-2002
 « Re: hondata s300 innovative lci install (hybridmath)« » 9:01 PM 5/12/2008 Reply  Edit

i say just to weld on another bung before the cat and put the Wideband there.. if you need anymore help with the install let me know. i have the same setup as yours. GL

perlmeister8




Offline

1484 posts [100%]
Denver
2-19-2004
 « Re: hondata s300 innovative lci install (hybridmath)« » 11:49 PM 5/12/2008 Reply  Edit

http://www.hondata.com/techplxwiring.html

It should be very similar to your innovative.


97 Civic Sedan EX
GT-Series equipped

http://www.tcperf.com

E-85



downest




Offline

1151 posts [100%]
Melbourne FL
7-28-2005
 « Re: hondata s300 innovative lci install (perlmeister8)« » 11:53 PM 5/12/2008 Reply  Edit

I assume you got the LC-1 or LM-1 from Innovative. They both have two analog outputs, you run one to the stock O2 pin (D14) and the other to your wideband input (I use D10). Run the LM programmer via the serial cable that comes with the wbo2 and program the first output to stock narrowband and the other to normal wideband (default).


Tom Downes
1991 CRX Si

Panducky Motorsports

Central Florida's only Authorized NepTuner/Dealer

CRX Community

hybridmath




Offline

192 posts [99%]
northern ct
4-27-2005
 « Re: hondata s300 innovative lci install (downest)« » 2:01 AM 5/13/2008 Reply  Edit

first off thanks for quick responses they are very much appreciated its a lc-1 got it all in a package deal
hondata s300 with boost option
walboro 255lph pump
omnipower 4 bar map
gm boost solenoid
chipped p28 with s300 installed
innovative lc-1 wideband with blue gauge
1300 shipped out next day was cheap compared to other places i looked what you guys think


Current : 94 dx hatchback fully built gsr getting rdy for boost
95 civic cx hatchback b18c1 apexi ws2 exhaust ran 14.611 stolen)
92 civic hatchback 00 integra B18b1 with gsr transmission 70 shot NOS (TOTALED)
93 civic 4dr b18a ys1 transmission (Totaled)

mike@OSTdyno.com




Offline

47 posts [100%]
harmony pa
5-2-2008
 « Re: hondata s300 innovative lci install (laziebun)« » 2:26 PM 5/13/2008 Reply  Edit

Quote, originally posted by laziebun »
i say just to weld on another bung before the cat and put the Wideband there.. if you need anymore help with the install let me know. i have the same setup as yours. GL

Since you already purchased the LC-1 I would go this route. For $7, buy an o2 sensor bung and weld it on. Run the Brown (wideband analog wire) from the LC-1 to the Hondata wideband analog in. Be sure to use the same ground source as the blue and white wires from the LC-1 for the ground for the Hondata wideband analog input ground

   

» Return to Engine Management and Tuning
Forum Jump
Quick Reply

Powered by ZeroForum 2.1.2b. ©2008 RelyNet, Inc.









Go