|
Maxbore.com
Always boring.
Offline
1751 posts [100%]
EF Garage, Florida
7-15-2001
|
| « Re: Blox manifold installed, high idle. Help (krucial7integra) | « » 10:03 AM 4/20/2008 |
Reply
Edit
|
4000 RPM means a rather big vacuum leak. I have found small leaks by using a compression tester and an air compressor. You just pressurize one of the cylinders making sure the intake valves on that cylinder are open and just listen for air. Engine off of course.http://WWW.MAXBORE.COM
Post counts don't mean a thing if you don't know what you are talking about.
|
insidiouseg-6
Offline
199 posts [100%]
south bay area ca
11-9-2006
|
| « Re: Blox manifold installed, high idle. Help (krucial7integra) | « » 7:18 PM 4/20/2008 |
Reply
Edit
|
i had that problem..but didnt idle at 4k..it was like at 2500..and it turned out to be my fitv..i just replaced it and it went away....u can also pull it off and check to see if the plunger is stuck open...
...........TEAM INSIDIOUS/ADVANCED MOTORWERKS....  T E A L - H A T C H - C L U B member #154 92 teal civic eg hatch
05 suzuki gsxr 600
|
krucial7integra
Offline
271 posts [100%]
Atl Ga
4-13-2004
|
just checked it earlier today again and I believe it is the FITV, because when I plug the bottom hole in the throttle body, it idles fine. I checked with napa auto parts and autozone but they don't seem to carry this part, any ideas on where to get it from besides the dealer?
|
gringo7718
Offline
618 posts [100%]
north cuba MIAMI
2-6-2002
|
fix your FITV for free. just open it up and tighten down the "plunger"http://www.honda-tech.com/zerothread?id=2153910
91 CRX B16 J1 trans. Intake, exhaust, HF front bumper support, 13lb. battery, no A/C.
Tein S-tech/Tokico illuminas. 15x7 Slips
|
krucial7integra
Offline
271 posts [100%]
Atl Ga
4-13-2004
|
thanks man, but I already tried that twice, its tight already, but air is still being sucked through when the car is warm, so I guess I'll have to replace the whole damn thing. Is this a dealership part only? because no one else carries it.
|
gringo7718
Offline
618 posts [100%]
north cuba MIAMI
2-6-2002
|
I just blocked mine off years ago. (metal plate and RVT high temp silicone)
91 CRX B16 J1 trans. Intake, exhaust, HF front bumper support, 13lb. battery, no A/C.
Tein S-tech/Tokico illuminas. 15x7 Slips
|
2fast4u831
I'm really 2slow
Offline
6508 posts [99%]
santa cruz county CA
1-19-2004
|
I also blocked minie. 6061 aluminum. 
H2B squad member #09
think fast, neukin , Turbogixxer , DVS
my project
myspace
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
im having this same prob.. i just put my blox IM on.. all sensors checked cleaned the iacv tightened the fitv.. and it still goes up and down from 1500 to 2k warm and cold.. also checked and rechecked all my vac hoses.. kinda at a loss right now =/also if im driving it around lets say 30mph 4th gear it will stutter back a forth.. does that maybe sound like a tps problem? a Modified by Koda at 11:21 PM 5/6/2008
Modified by Koda at 11:28 PM 5/6/2008
[My MySpace]
|
Maxbore.com
Always boring.
Offline
1751 posts [100%]
EF Garage, Florida
7-15-2001
|
If the TPS is the problem, then you would have a CEL because of it.
What throttle body are you using?
Post counts don't mean a thing if you don't know what you are talking about.
|
emotionisdead
If I Come to New York....
Offline
3350 posts [100%]
....Could I Sleep on Your Floor.. Reno
12-27-2003
My Gallery
|
Did you make sure you got all the old gasket off? Throttle body and Intake Manifold? I installed a blox manifold on my GSR nad It idles just fine. I also have a Omni throttle body that doesn't use that fast idle valve thing under the stock GSR throttle body.
♥ EMOmob♥  ♥ Please Check Out My Band's Page.
Click Here!!♥
|
groundzerocivic
Offline
216 posts [100%]
Dundalk MD
11-21-2006
|
| Quote, originally posted by emotionisdead » |
I installed a blox manifold on my GSR nad It idles just fine. I also have a Omni throttle body that doesn't use that fast idle valve thing under the stock GSR throttle body. |
i got a blox mani and skunk2 TB....no fast idle on it.....(sux if i drive the car in cold weather....gotta let warm up for a while 2 get alitte bit of heat.....  )
| Quote, originally posted by Combustion Contraption » | | Loctite and impact everything down with impact gun on "high" |
| Quote, originally posted by prettylew » |
not everything needs to be "lug nut" tight |
R.I.P.--DAD 11/7/49 - 3/30/07  
http://www.myspace.com/lordvadercivic
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
| Quote, originally posted by emotionisdead » | | Did you make sure you got all the old gasket off? Throttle body and Intake Manifold? I installed a blox manifold on my GSR nad It idles just fine. I also have a Omni throttle body that doesn't use that fast idle valve thing under the stock GSR throttle body. |
im going to check the gasket today with some thottle body cleaner today see if i got any leaks.. if i cant see anything ima just take it all apart again and recheck everything again
[My MySpace]
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
| Quote, originally posted by Maxbore.com » | If the TPS is the problem, then you would have a CEL because of it.
What throttle body are you using? |
just useing a stock gsr TB
[My MySpace]
|
Maxbore.com
Always boring.
Offline
1751 posts [100%]
EF Garage, Florida
7-15-2001
|
I don't have the blox manifold, but if you have a OBD1 GSR TB, you need to make sure the TB seals all the way along the bottom of the manifold.
Post counts don't mean a thing if you don't know what you are talking about.
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
ok.. i sprayed the IM gaskets and it stutters out some.. so im going to be taking off the IM and see how much of the old gasket is on there.
[My MySpace]
|
boost'd_crx
Honda-Tech Member
Offline
543 posts [100%]
CA
12-16-2004
|
| Quote, originally posted by Koda » | | ok.. i sprayed the IM gaskets and it stutters out some.. so im going to be taking off the IM and see how much of the old gasket is on there. |
make sure you get all the old gasket off. it should be your problem because you have a very big vac. leak.
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
| Quote, originally posted by boost’d_crx » | make sure you get all the old gasket off. it should be your problem because you have a very big vac. leak. |
ok.. im hopeing it is.. i should find out tonight when i put it back on afterwork..
[My MySpace]
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
hey.. just wanted to say thanks to everyone.. car is all fixed now =D
[My MySpace]
|
AMLS4dr200whp
Offline
1441 posts [100%]
somewhere ukno
1-24-2005
|
| Quote, originally posted by Koda » | | hey.. just wanted to say thanks to everyone.. car is all fixed now =D |
nice problem solved
stock bottom end all motor ls 
dyno 160whp and 127ft/lbs tq neptune tuned
Now: Turbo LS on stock bottom end
dyno: 325whp and 265ft/lbs tq neptune tunedDB squad #88 Vouches: got plenty check my bio for info
|
low'n'fro
Offline
65 posts [100%]
H Town TX
5-25-2006
|
Was it the FITV or was it something else that caused the problem?
|
-Darren-
Offline
1163 posts [100%]
tikrit iraq
12-18-2001
|
so was the problem the throttle body gasket?
NJ c00l guy #1. 
#1 Dad
Virgin Island Crew #1LS head f/s in NJ....$20
http://www.hondamarketplace.co...14681
|
Koda
Offline
70 posts [100%]
Mesa az
10-18-2004
|
| Quote, originally posted by -Darren- » | | so was the problem the throttle body gasket? |
yeah it was.. turns out acura gave me the wrong one. =/
[My MySpace]
|
| | |
