 |
|
|
|
|
|
| Author |
Post |
earl
Moderator
Offline
8404 posts [100%]
Irvine CA
6-24-2001
|
| DSS Drive Shaft Shop Axles | « » 4:39 PM 7/30/2006 |
Reply
Edit
|
IM Ninesecrx with any questions
Level 0 Axles (Factory Style Replacements)
They use a chrome moly center bar and a billet inner c.v. with the oversized tripod. A new heat treating process is also used on the 1117 billet outer c.v. The outer c.v. is made with a single arc design which allows a wear advantage over the factory Honda dual arc design that tends to wear out prematurely. This is a superior axle for any stock replacement or swap. These axles come with green boots and removable ABS ring's. Price listed is for a complete set of left and right. The axles are designed as an alternative to poorly made re-builds and as inexpensive units for swaps. Although these are made superior to stock axles, they are NOT intended for racing use.
Warranty covers manufacturing defects only, no racing coverage
Our price $295 Shipped
Level 2.9 Axles (475whp Forced Induction/AllMotor)
These axles are for the extreme street/track car up to 475WHP forced induction or all motor. They are the result extreme track testing! The inner and center is borrowed from the track tested level 3 system using a new proprietary material and have solid torsional center bars, chrome moly spline plug and high grade inner housings with oversized tripod. What makes this stand apart from the rest is the new outer C.V. made from high grade chrome moly that has one of the wildest heat treats known to man. During destructive testing it broke a 300m bar! It's designed to fit the standard 26 spline size of the Honda/Acura platforms. These axles come with blue boots and removable ABS rings. Price is for both left and right axles.
Our price $670 Shipped (Integra and Civic only)
(Add $50 to above price for Accords, Preludes and RSXs) Level 3.9 Axle/Hub System (600whp)
Applications for many of the popular Honda civic and Acura Integra’s. Information coming soon...
Our Price $1080 Shipped
(Add $100 if ABS rings are required) Level 5.9 Axle/Hub System (1000whp)
The new level 5.9 axle/hub set is similar to the previous level 5 system but with a major upgrade, the inner CV. Over the past 2 years, DSS has noticed the system to be very strong but had one fault, the inner CV could become damaged if not handled properly! The higher HP cars seem to have the transmissions changed often. During the swap, the axle was left attached to the transmission but hanging at the wheel (outer in the air). If pressure was put on the outer CV, it would damage the retainer that holds the tripod needles on the inner. Over time the needles would fallout (not good). What DSS has come up with is a new ball & cage inner CV made from high quality chromoly. This inner CV now has 6 contact points and is stronger than the Porsche 930 (108mm) CV (same CV used by many high dollar systems).This along with the 33 spline outer and 36 spline bars makes them the strongest set of axles to date. The system is designed for 1000WHP and any size tire you want to use!
Our Price $1,550 Shipped
(Add $100 if ABS rings are required) Honda/Acura Rally/Road Race System
This is a specially designed road/rally axle set. DSS has done extensive racetrack testing to bring you these axles. This system is designed for 300HP (not drag). What we have learned is that the parts that DSS makes for drag racing aren’t exactly the right parts for road or rally racing. The parts have to take long-term punishment of heat and stress. What DSS have done is make an axle set directly for road or rally punishment. DSS starts with the chromoly center bar, uses their oversized tripod inner housings and then get a outer CV with a single arch design cage. Factory Acura/Honda design has a dual arch design so every time you turn, the ball goes over a sort of a peak in the ball track making it fail prematurely. Then DSS takes all parts, polish and match them carefully to almost pre-break in state. The end result is smooth movement so there is no heat buildup. DSS then uses a special boot made from a material called Hytrell. This handles the heat better. They use a super high grade synthetic grease designed for the 24 hour Lemans cars. DSS also vents the boots to keep internal and external temps even. Now you can keep your car on the track without worry of parts failures.
Our Price $555 Shipped Honda S2000 level 2.9 550HP axles
The 2.9 axles are now available! These axles are for the extreme street/track car up to 550HP forced induction or all motor at the wheels. These axles are the result extreme track testing! The inner and center is borrowed from the track tested level 3 system using a new proprietary material and are solid torsional center bars, chrome moly spline plug and high grade inner housings with oversized tripod. What makes this stand apart from the rest is the new outer C.V. made from high grade chrome moly that has one of the wildest heat treats known to man. During destructive testing it broke a 300m bar! It's designed to fit the standard 28 spline size of the Honda/Acura platforms. These axles come with blue boots and removable ABS rings. Price is for both left and right axles.
Our Price $845 shipped Honda S2000 level 5 rear axle/hub kit (1000HP)
This Is with out a doubt the finest axle system you will find for this car. The larger outer c.v. and center bar (40 and 50%) bolt on inner and ready to go. Good for 1000WHP.
1.Stock S2000 Rear
2.Diff Techniques R200 Conversion
3.Casper Fabrications 8-3/4 Rear
Our Price $1560 shipped S2000 U-joint Conversion Shaft
This is a replacement shaft for the S2000 platform. The factory shaft has a very small c.v. on each end. The c.v. ends are quite weak and under extreme abuse tend to fail both prematurely and unexpectedly. The shaft has a set of 7075-T6 aluminum plates that convert the shaft over to standard flange mounts for a u-joint style shaft. This along with the DSS shaft enables the system to handle 650whp. The kit comes complete with (2) aluminum conversion plates, shaft and all hardware. When you're serious about your S2000's drive train and its time to take it to the next level remember Driveshaft shop helps you get there
Our Price $615 shipped 
Modified by earl at 3:24 PM 8/31/2007
WE SELL Benson Machine Sleeved blocks & cranks
SuperTech SS Valves, Dual Springs, Ti Retainers
CP Pistons & rings
ACL Bearings
Pauter - Eagle - Manley Rods
DriveShaftShop Axles
ATI Dampners
BDL/STR Products
PWR Radiators & Intercoolers
Quaife Dif
Head porting by PortFlow now availableCustom built race and street engines..K, B, H, F, D cores in stock Have a Question?..Call 714.688.0222 (shop)
http://www.laskeyracing.com
|
|
Boosted_JDM
Offline
186 posts [98%]
7-4-2006
|
| « Re: DSS Drive Shaft Shop Axles (earl) | « » 8:33 PM 7/30/2006 |
Reply
Edit
|
When will the DSS Stage 5, with Ball and Cage design, be ready for the public.
|
earl
Moderator
Offline
8404 posts [100%]
Irvine CA
6-24-2001
|
| « Re: DSS Drive Shaft Shop Axles (Boosted_JDM) | « » 6:54 PM 11/21/2006 |
Reply
Edit
|
Now available
WE SELL Benson Machine Sleeved blocks & cranks
SuperTech SS Valves, Dual Springs, Ti Retainers
CP Pistons & rings
ACL Bearings
Pauter - Eagle - Manley Rods
DriveShaftShop Axles
ATI Dampners
BDL/STR Products
PWR Radiators & Intercoolers
Quaife Dif
Head porting by PortFlow now availableCustom built race and street engines..K, B, H, F, D cores in stock Have a Question?..Call 714.688.0222 (shop)
http://www.laskeyracing.com
|
bigfigman
Offline
616 posts [100%]
Sierra Vista AZ
9-15-2006
|
| « Re: DSS Drive Shaft Shop Axles (earl) | « » 8:28 PM 11/28/2006 |
Reply
Edit
|
| Quote, originally posted by earl » | | Now available |
whats the price difference? never mind, i read the whole post. you have PM.
SOME VOUCHES: http://www.hondamarketplace.com/zerothread/1830574
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (bigfigman) | « » 5:39 PM 12/27/2006 |
Reply
Edit
|
| Quote, originally posted by bigfigman » | whats the price difference? never mind, i read the whole post. you have PM. |
PM me guys if you need help with the DSS product line. Thanks, Mike
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (ninesecrx) | « » 5:43 PM 8/31/2007 |
Reply
Edit
|
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (ninesecrx) | « » 5:43 PM 9/27/2007 |
Reply
Edit
|
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (earl) | « » 8:45 PM 11/5/2007 |
Reply
Edit
|
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
EK_vzla
Offline
748 posts [100%]
caracas/venezuela
4-30-2003
|
pm`d
ek gt35r boosted
honda fit 2006 just for show
ford sport trac 2007 DD
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
Tchleung
Offline
2490 posts [100%]
Penticton BC
1-23-2003
|
Curious about them fixing the inner spider on the 5.9 axles, was this an issue with their models below the 5 series? I'm looking at getting the 3.9's from you guys in spring but that inner spider needles falling apart doesn't sound promising.
1990 Acura Integra GS-T
Old 2006 Setup
Best ET to Date - 12.02 - Street Tires(17" BFG DR), Best MPH to Date - 129.18mph, Best 60' to Date - 2.07
New 2008 Setup
No Track Times Yet - 484whp/313wtq @ 21psi
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
The level 3.9's are actually the same as the old level 5's. They are pretty strong. But of course the ball and cage inner of the 5.9 is a big step up!
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
Tchleung
Offline
2490 posts [100%]
Penticton BC
1-23-2003
|
Hrmm.. is that inner spider clip breaking off a common problem? I'm jsut worried installing them the first time and them breaking on me...BTW, thanks to your head and block, my car did 484whp/313wtq at 21psi on a mustang dyno the other week
1990 Acura Integra GS-T
Old 2006 Setup
Best ET to Date - 12.02 - Street Tires(17" BFG DR), Best MPH to Date - 129.18mph, Best 60' to Date - 2.07
New 2008 Setup
No Track Times Yet - 484whp/313wtq @ 21psi
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| Quote, originally posted by Tchleung » | | Hrmm.. is that inner spider clip breaking off a common problem? I'm jsut worried installing them the first time and them breaking on me... BTW, thanks to your head and block, my car did 484whp/313wtq at 21psi on a mustang dyno the other week |
Only way I see issues is when people change the transmission and they leave the axles hanging at a weird angle for a long time. This is rare as well and I would not worry about it. Glad the engine worked out for ya, let me know when you are ready for a set. Keep in mind I used the other axles on my crx racecar making well over 700hp and changed the transmission all the time and never had one break ever.
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
vti2
Offline
532 posts [100%]
Dortmund NRW
7-9-2002
|
Hi bought a 3.9 set but it came without ABS rings, does anybody knows if i can buy it seperatly?
EARL Arturbo
B18b1 Sonny
b18bturbo ek9vboi2
knuckleneck dasher
Daily driver:2004 Mercedes C240T Avangard
Race car: 500+ WHP Civic EG9 on PUMP on building 
R.I.P Earl. I will be missing you
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| Quote, originally posted by vti2 » | | Hi bought a 3.9 set but it came without ABS rings, does anybody knows if i can buy it seperatly? |
You would have to send the axles back to DSS because they have to machine the outters to put the ABS rings on, you can not just buy the rings.
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
vti2
Offline
532 posts [100%]
Dortmund NRW
7-9-2002
|
Shit, i only notice this problems with the rings when they were hear at me Me in Germany. 
EARL Arturbo
B18b1 Sonny
b18bturbo ek9vboi2
knuckleneck dasher
Daily driver:2004 Mercedes C240T Avangard
Race car: 500+ WHP Civic EG9 on PUMP on building
R.I.P Earl. I will be missing you
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (earl) | « » 5:10 PM 1/30/2008 |
Reply
Edit
|
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
imjustakid
Offline
42 posts [100%]
GIXXERTOWN CA
4-19-2006
|
can you pm a price for 3.9 axles for eg with b series
picked up
WTB: B18B STROKER KIT
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| Quote, originally posted by imjustakid » | can you pm a price for 3.9 axles for eg with b series
picked up |
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
bkukes15
Offline
46 posts [100%]
eastern washington
12-2-2007
|
| « Re: DSS Drive Shaft Shop Axles (earl) | « » 1:09 AM 2/23/2008 |
Reply
Edit
|
I bought the 2.9's and now I think I need the 3.9's. This build is getting out of hand. Help me Mike . lol.Laskey Racing All the way. -Kukes
Boosted H22-T EG underway.thanks to..
LASKEY Racing
SKunk2 Racing
PortFlow.com
Boostfed.com
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (bkukes15) | « » 2:00 PM 2/24/2008 |
Reply
Edit
|
| Quote, originally posted by bkukes15 » | | I bought the 2.9's and now I think I need the 3.9's. This build is getting out of hand. Help me Mike . lol. Laskey Racing All the way. -Kukes
|
Haha, it always seems to happen that doesn't it? You know how to get a hold of me
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
ninesecrx
Laskeyracing.com
Offline
5727 posts [100%]
Anaheim CA
3-27-2002
|
| « Re: DSS Drive Shaft Shop Axles (earl) | « » 9:32 PM 3/27/2008 |
Reply
Edit
|
http://www.laskeyracing.com Custom built race and street engines..K, B, H, F, D cores in stock Drive Shaft Shop axles, west co. distributer BDL cam gears, throttle bodies and fuel rails... CP pistons PWR Intercoolers and Radiators Benson sleeved blocks Eagle and Pauter rods ATI Dampers Laskey Racing (714) 688-0222 <--HAVE A QUESTION, CALL THE SHOP...WE ARE HERE TO HELP! Dad (Earl) thanks for everything, I miss you but don't worry...I will make you proud
|
boosstboy
Offline
406 posts [100%]
chicago burbs IL
9-5-2004
|
| « Re: DSS Drive Shaft Shop Axles (ninesecrx) | « » 11:02 PM 3/27/2008 |
Reply
Edit
|
pm'd
precision turbo on all my turbo stuff
td autowerks for my full ferrea head package
rld fab for my manifold
laskey racing for my built block
for me for everything else, priceless
|
02vtecsir
Offline
135 posts [100%]
spangdahlem germany/from maryland germany
7-9-2003
|
how much shipped to military apo
00 si/jdm type r swap....w/ extras-----220whp/ former domani front end conversion---thanks mr. hit and run
represent--------------Team-uv.com-----miltary members in the car scene stationed in germany expanding chapters now in the U.S.
|
| | First 1 2 > Last |
|
Powered by ZeroForum 2.1.2b. ©2008 RelyNet, Inc.
|
|
