94 Integra GSR mid-engine RWD H22A4 conversion

[rochesterricer]

Originally Posted by sdsviet wtb: aem cai bypass only 2.5inch. used or new Did I miss something? Does it say classifieds in the thread title?

This ad is not displayed to registered or logged-in members. Register your free account today and become a member on Honda-Tech!

[HondaRcB]

I remeber reading this thread a few weeks ago and becoming highly intrigued, but I must have forgotten about it and stopped reading. I found it again today and can't believe the progress. This is fcuking awesome. The amount of work and knowledge going into this is incredible. I'm sure you're having a blast and keep up the good work man.

[hondaZvic]

Originally Posted by rochesterricer

Did I miss something? Does it say classifieds in the thread title?

lol... BAN!!!! hahahah

[ATS*Mark]

wowowowowowowoowowowowowowowow such a sick project

supscribed.

[JDMorgan]

Originally Posted by RaceCity_USA

An s2k drive train is for front engine RWD

you can use an s2k motor with an rsx-s or rsx-r tranny, and you will have a nice 6 speed setup. they were using them in lotus' a little while back

Originally Posted by RaceCity_USA

The frame work is done. What do you think should be done to "finish where the rad support would be"?

i just didnt think the frame would end so abruptly. are you planning a firewall between the cockpit area and the gas tank later on?

[Sliced Beard]

ok, I am getting tired of seeing this.............time to rant

I am tired of watching people WASTE bandwidth by posting in a thread just so it can be in their watched topics list. Are you people freaking blind? Do you not see the SUBSCRIBE link in the top right hand section of your screen, or are you entirely too ignorant to read? I say this becasue, every time you post something up on this board it COSTS MONEY!!!! Someone has to pay for hosting/server fees in order to keep this website alive. I cannot understand why people post up like five words in a horrid attempt to make a sentence or comment then like two lines below the write "subscribing" .........just hit the freaking subscribe button and let the hosting program do the work for you and STOP WASTING MONEY!!!

[.dave]

Originally Posted by DirtySol

ok, I am getting tired of seeing this.............time to rant

I am tired of watching people WASTE bandwidth by posting in a thread just so it can be in their watched topics list. Are you people freaking blind? Do you not see the SUBSCRIBE link in the top right hand section of your screen, or are you entirely too ignorant to read? I say this becasue, every time you post something up on this board it COSTS MONEY!!!! Someone has to pay for hosting/server fees in order to keep this website alive. I cannot understand why people post up like five words in a horrid attempt to make a sentence or comment then like two lines below the write "subscribing" .........just hit the freaking subscribe button and let the hosting program do the work for you and STOP WASTING MONEY!!!

Calm down...seriously. If anything you should bitch at the people in the Classifieds forum who bump their own topics over two pages long. You're guilty of that yourself.

Originally Posted by KraZEtEggIE

i just didnt think the frame would end so abruptly. are you planning a firewall between the cockpit area and the gas tank later on?

I'd assume that he'd do this. Someone correct me if I'm wrong, but don't most sanctioning bodies require some sort of seperation between the drivers compartment and gas tank?

As far as getting air in there, I still say replace the rear side windows with Lexan pieces with NACA ducts in them. Its certainly more aerodynamic than a blingin' roof scoop from Paul Walker.

http://www.quickcar.net/cooling/cp_nacaduct.html

[CivicHatchback14]

[quote=DirtySol]ok, I am getting tired of seeing this.............time to rant

I am tired of watching people WASTE bandwidth by posting in a thread just so it can be in their watched topics list. Are you people freaking blind? Do you not see the SUBSCRIBE link in the top right hand section of your screen, or are you entirely too ignorant to read? I say this becasue, every time you post something up on this board it COSTS MONEY!!!! Someone has to pay for hosting/server fees in order to keep this website alive. I cannot understand why people post up like five words in a horrid attempt to make a sentence or comment then like two lines below the write "subscribing" .........just hit the freaking subscribe button and let the hosting program do the work for you and STOP WASTING MONEY!!!


Quit crying....... you don't pay for it.

[Sliced Beard]

you are correct, I don't pay for it buyt there is someone out there that does (Dustin)

[Tinker219]

Originally Posted by DirtySol

you are correct, I don't pay for it buyt there is someone out there that does (Dustin)

and any sponsors that advertise here

You will have to do a complete firewall, simply because of exhaust fumes re-entering the cabin. My del Sol was a severely affected candidate of this. Some under-baffling may have helped keep the exhaust fumes behind the rear bumper, but I just concentrated on sealing the firewall as best as possible.

[Stoich EG2]

I am damn jealous of Tinker's and Race's projects... one day... it will be me doing this stuff

[BaGGed HoNDa]

How is the progress going? I can't wait to see the finished product, this really has inspired me to go out and plan my own projects.

[green91]

great project.. can't wait to see it done! i bet putting the motor in will be a trick

[Stoich EG2]

Originally Posted by green91

i bet putting the motor in will be a trick

I think it'll be just as easy as any other swap. he has the hatch off so it'll be more room up top. i cant wait to see this thing in action. i wonder if it'll be like the drifting integra i've seen.

[Tinker219]

The way the del Sol was designed, I just have to remove the intake manifold, and it drops right out, no problems.
As for drifting, the del Sol was VERY twitchy. Ie, if you lost the ass end, its gone until youre done doing your 1080 w/6 cars hot behind you. Maybe its because this is the first RWD car Ive driven? Probably

[Sliced Beard]

let me drive that bad boy.......I grew up driving T/A's, Vettes and Camaro's

[Blaise]

Originally Posted by Tinker219

Why not mess w/tubing? I thought it was easier than trying to weld peices of old sheet metal together. Will you be caging this later on?

heres a vid of the Sol...motor has to come back out, h22 block back in over next weekend(hopefully).
http://www.inductionperformanc...p.wmv

Those were some pathetic donuts. Oh well, crazy fabrication

[Tinker219]

it rips "donuts" just fine after some suspension tweaking. Because after all, thats what I built it for, doing donuts.

[Sliced Beard]

haha, you tell em' Cody

[BigPlansNoMoney]

Looks better and better everytime I check up...

Wish I had your skills

[B18C1CYA]

wow i just looked at the whole post and man it looks sick, i think it is cool how cody did his with a cage and tubing , and you are doing it with the unibody parts, very cool guys , keep up the good work

[fookle]

Originally Posted by Tinker219

it rips "donuts" just fine after some suspension tweaking. Because after all, thats what I built it for, doing donuts.

speaking of which, is that thing boosted yet cody? also, got any updated video?

[Stoich EG2]

i think it's sold =X

[RaceCity_USA]

===

[Stoich EG2]

this has got to be the cleanest RWD conversion i've ever seen. and you're doing it in your own garage! crazy...