k24/k20 build with dyno numbers
#1
Honda-Tech Member
Thread Starter
Join Date: Jan 2008
Location: anaheim, ca, usa
Posts: 1,944
Likes: 0
Received 0 Likes
on
0 Posts
k24/k20 build with dyno numbers
Ok finally done with the build there are 4 dynos starting from where i got it since today
This thing REVS like a bike and it has lots of tq
Heres the dynos:
Made 274.8hp and 200tq on the last run will post that dyno sheet tomorrow
Made 293.1 and 216tq the most i made that day was 294hp
new numbers
Heres the list of parts:
Block
k24a4 87.5 bore honed and hot tanked
Wiseco 87.5 12.5 cr pistons with deep pocket valves
BP Pro I beam rods
crank was balaced and polished and knife edge
acl race series bearing
Head
Blueprint stage3 cams
IPS retainers and spring combo Im still in the stock valves
Bolt ons
rbc manifold
Hytech replica header
3.0inch exhaust
CAI
AEM EMS
550 inj
The runs were done on a DYNOMITE with 93oct
Thanks to IMPORT AUTO PROS for tunning and building this motor
and to ROBBIE from blueprint for the good prices and quality parts
This thing REVS like a bike and it has lots of tq
Heres the dynos:
Made 274.8hp and 200tq on the last run will post that dyno sheet tomorrow
Made 293.1 and 216tq the most i made that day was 294hp
new numbers
Heres the list of parts:
Block
k24a4 87.5 bore honed and hot tanked
Wiseco 87.5 12.5 cr pistons with deep pocket valves
BP Pro I beam rods
crank was balaced and polished and knife edge
acl race series bearing
Head
Blueprint stage3 cams
IPS retainers and spring combo Im still in the stock valves
Bolt ons
rbc manifold
Hytech replica header
3.0inch exhaust
CAI
AEM EMS
550 inj
The runs were done on a DYNOMITE with 93oct
Thanks to IMPORT AUTO PROS for tunning and building this motor
and to ROBBIE from blueprint for the good prices and quality parts
Trending Topics
#8
Honda-Tech Member
iTrader: (1)
Re: k24/k20 build with dyno numbers
#10
Honda-Tech Member
Thread Starter
Join Date: Jan 2008
Location: anaheim, ca, usa
Posts: 1,944
Likes: 0
Received 0 Likes
on
0 Posts
Re: k24/k20 build with dyno numbers
#16
Honda-Tech Member
Re: k24/k20 build with dyno numbers
very nice numbers, you must be proud... i envy you. i will be going with the k24 block when i decide to switch over to k-series. did you use the original k24 head?
#18
Honda-Tech Member
Thread Starter
Join Date: Jan 2008
Location: anaheim, ca, usa
Posts: 1,944
Likes: 0
Received 0 Likes
on
0 Posts
#21
Junior Member
Join Date: Apr 2009
Location: subs of philly
Posts: 110
Likes: 0
Received 0 Likes
on
0 Posts
Re: k24/k20 build with dyno numbers
i am soooo glad i am going through with this build after seeing these setup going into to the 300/200 range,with little done to them is kickass
#23
Honda-Tech Member
Thread Starter
Join Date: Jan 2008
Location: anaheim, ca, usa
Posts: 1,944
Likes: 0
Received 0 Likes
on
0 Posts
Re: k24/k20 build with dyno numbers
Sure let me know if you have any questions pm me
I'm thinking of a nos setup i seen floating around for cheap
I'm having problems with it the clutch is almost done lol
I'm thinking of a nos setup i seen floating around for cheap
I'm having problems with it the clutch is almost done lol