Honda and Acura Technical Forums

Fuster_Cluck · 08-01-2007, 04:34 AM

I'm new to this. I'm sure there are others out there. I recently picked up my K20a2 swap, snapped some pics, and want to figure out everything I have labeled. I know some of the basic parts, but there are a few I have no idea about. So, let's get the parts labeled and hopefully most will learn a thing or two about this great motor

Also, if anyone knows what needs to be removed when installing into an EF, EG, EK, EP, DA, DC, etc........ post up the info and I'll add it to the list

Entire shot:
X: A/C compressor
Y: Water Pump
Z: Auto Tensioner Pulley
1: Auto Tensioner
2: A/C compressor harness
3: Passenger side engine mounting bracketX:
4: Charge harness
5: Intake manifold
6: Coolant entrance or exit?
7:
8:
9: Battery ground
10: Clutch slave cylinder
11: Starter soleniod
12: Starter
13: Power Harness for Alternator
14:
15: Intake manifold brace
16: Intake Air Control Valve (IACV) ??
17:
18: __________ (TPS)
19:
20:
21:
22:
23:
24: Shifter Cables connection
25: Bolt for front engine mount?
26: Bolt for front engine mount?
27: Bolt for front engine mount?
28: Evap purge?
29:
30:
31: Throttle body / Opening for intake
32: coolant line to/from throttle body or Intake Air Control Valve (IACV)?
33: Transmission breather cap?
34:
35:
36: Bad view will get more pics up to clarify part
37:
38:
39:
40:
41: Fuel Rail
42: Fuel injectors harness
43: Injector #?
44: Injector #?
45: Injector #?
46: Injector #?
47:
48:

Question: Do you relocate #9 battery ground when installing the motor into a 92-95?

Entire shot:

Top Left:

Top Right:

Bottom Right:

Bottom Left:

In case I decide to run A/C down the road (yeah right):

Entire rear shot:

A: Coolant outlet /inlet to heater
B: Vehicle Speed Sensor, or VSS
C: Clutch line
D: Tranny ground
E: Main engine harness
F: Oil Filter
G: Coolant drain bolt
H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: Vtec Solenoid
N: VTEC oil pressure sensor
O: Looks to be part of the manifold vacuum that would go to the brake booster
P: Evap control valve hardline. Most people remove both of those hardlines
Q: VTC oil control solenoid valve
R: Vin plate
S: Exhaust manifold heat shield
T: Header
U: Charge harness
V: Tranny bracket

Entire rear shot:

Top Left:

Top Right:

Passenger side:

Question: What do I need to remove to add the EP3 idler system?

H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: VTEC Solenoid
N: VTEC oil pressure sensor
Q: VTC oil control solenoid valve
W: Alternator
X: A/C compressor
Y: Water Pump
Z: Auto Tensioner Pulley
1: Auto Tensioner
2: A/C compressor harness
3: Passenger side engine mounting bracket
Another close up:

M: Vtec solenoid
N: VTEC oil pressure sensor

One more close up:

PS <> If I have something labeled wrong, feel free to let me know and I will correct it.

Parts to Remove before Installing a k20a2 into:

92-95 Civic
1.
2.
3.

96-00 Civic
1.
2.
3.

90-93 Integra
1.
2.
3.

94-01 Integra
1.
2.
3.

Hope you enjoyed/learned something from this thread

Modified by Hybrid93Hatch at 11:31 AM 8/3/2007

This ad is not displayed to registered or logged-in members.
Register your free account today and become a member on Honda-Tech!

Bense · 08-01-2007, 09:33 AM

nice thanks for contributing

Fuster_Cluck · 08-02-2007, 02:30 AM

Quote:

Originally Posted by Bense

nice thanks for contributing

No problem. I like to help out the community whenever I can.

124 views and no one can contribute

hpi247 · 08-02-2007, 07:31 AM

10 the slave cylinder?

Relic1 · 08-02-2007, 09:14 AM

great thread.

my poor contribution.
10 - clutch slave cylinder
11 - starter solinoid
12 - starter
15 - intake mani brace
16 - IACV?
17 - coolant line to/from TB or IACV?
18 - TPS
24 - radiator hose mount?
25 - rear engine mount?
26 - rear engine mount?
27 - rear engine mount?
28 - EVAP purge?
31 - throttle body
32 - coolant line to/from TB or IACV?
33 - trans breather cap?
36 - heater hose mount?
41 - fuel rail
42 - fuel injector harness

ekb16 · 08-02-2007, 11:56 AM

didnt you post this on k20a.org also?

Fuster_Cluck · 08-03-2007, 08:32 AM

Thanks guys for your contributions

Quote:

Originally Posted by ekb16

didnt you post this on k20a.org also?

Yes, it's also posted on K20a(dot)org

2007korinne · 01-30-2009, 10:09 PM

This is amazing...awesome job! You should do this for the B-series too

08-01-2007, 09:33 AM	#2
Bense Moderator Join Date: Mar 2003 Location: Clemson, South Carolina! Posts: 9,211	nice thanks for contributing __________________ http://people.clemson.edu/~ABense

08-02-2007, 09:14 AM	#5
Relic1 Member Join Date: Oct 2002 Location: chicago burbs, Il, USA Posts: 4,497	great thread. my poor contribution. 10 - clutch slave cylinder 11 - starter solinoid 12 - starter 15 - intake mani brace 16 - IACV? 17 - coolant line to/from TB or IACV? 18 - TPS 24 - radiator hose mount? 25 - rear engine mount? 26 - rear engine mount? 27 - rear engine mount? 28 - EVAP purge? 31 - throttle body 32 - coolant line to/from TB or IACV? 33 - trans breather cap? 36 - heater hose mount? 41 - fuel rail 42 - fuel injector harness __________________ the civic hatchback community

08-02-2007, 11:56 AM	#6
ekb16 Member Join Date: Feb 2005 Location: ca Posts: 2,490	didnt you post this on k20a.org also? __________________ B.A.R. member as of 3/18/09 JDM gsr in 98 hatch Need Honda helms manual - pm me $60shipped any book Voches: chickwithastick,93allmotorcoupe,jomama,punoy69,Tom theman70

01-30-2009, 10:09 PM	#8
2007korinne Junior Member Join Date: Sep 2008 Location: Janesville, WI, USA Posts: 8	Re: K20a2 complete (exterior) motor disected & labeled! Pics This is amazing...awesome job! You should do this for the B-series too __________________ My boyfriend wears a shirt that says, "My girlfriend does the driving".

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search